Lian Li Armorsuit PC-P50R Dragon Case Review

The Lian Li Armorsuit PC-P50R is a mid-size tower with a sleek black exterior, and some serious red highlights. That is until you get past the colossal dragon figure on the side panel and look through the clear window. Taking advantage of the full aluminum construction, Lian Li let the anodizing team loose on the interior with a bucket of red die, and the result is stunning. The case also comes fully outfitted with four red LED fans, two 120mm front and back, and two 140mm on top that enhance the red theme of the interior. Lian Li has never been shy about dressing up its signature products. They've produced some of the most original and striking PC gaming cases that I can remember. Unlike the wild show cars that are never meant to turn a wheel, these chassis get pushed right into the mainstream retail channels. Lucky us! Benchmark Reviews is pleased to review this special AMD edition of the Lian Li PC-P50 series.

Special attention has been focused on the tool-free features of the case, including an impressive PSU clamp that will hold the largest units much more securely than the usual four small screws on the back panel. The slick expansion card clamps are not only tool-free, they are artfully designed, as well. The HDD cage and removable drive trays have a flexible mounting arrangement that allows the case to easily accept the largest graphics cards on the market. Dual 140mm fans on the top surface effectively extract hot air from inside the case, aided by the rear fan, which is also an exhaust. The case is lightweight, at 6.6 kg, and would be suitable for transport to LAN parties, even without a handle to make it easy to carry.

Many of the features of the PC-P50R aid in getting a full gaming system built quickly, or reconfigured with different components in a short amount of time. The cable management is simple, yet effective. The drive cage is easily removed from the front of the case, as are all nine drive bay covers, all without tools. The drive cage can also be slid forward without removing it completely, so you can move it out of the way without disconnecting any of the drives. This provides unparalleled access to an area of the case where most of the system cables pass through, which is usually one of the choke points in component installation. Enough about what I think for now, let's take a look at the actual features and specifications, direct from Lian Li.

Lian Li Armorsuit PC-P50R Features

• The cutting edge tool-less design is an important mission in 2009 Lian Li cases.
• It is convenient for those who are building systems faster, or swapping out components often. For example when installing the 5.25" optical drive, it just slide the drive into the 5.25" bay, and close the mounting bar to secure the optical drive, it is as simple as that not only for optical drive but also for:
• The installation of the hard disk is very easy, and tool-less. It is only required to put the hard disk into the aluminum rack and closing it with special designed clip, then, slide it into HD cage. It is all secured with anti vibration rubber ring.
• The installation of PCI add on card, it can be done as simply as open the aluminum arm holder, insert the add-on card to the motherboard slots, and close the aluminum arm holder. The additional rubber padding on the aluminum arm assists in gripping the card bracket and securing it firmly.
• The new ARMORSUIT PC-P50R is special designed for the LAN party groups. It is a mid-tower case, but internally allows the latest graphics cards in combination with the best thermal dynamics. Again, all the internal installation can be done without tools, and is easily adjustable to optimize your hardware setup. Especially in the advent of adding in new graphics cards, or extra fans when adapting to various LAN party needs and environments.
• ARMORSUIT PC-P50R uses large size cooling fans to remove the system heat faster and quieter as well as keeps the system more stable.
• The both front and top cover are detachable without tool. It is just simply lift up cover then can be access for maintenance.
• ARMORSUIT PC-P50R has no front door design; users can access the drive easier.
• The fans on the top panel are mounted with Lian Li's new anti-vibration fan mounting system; the rubber ring grommet absorbs the vibration, keeping the case silent.
• The ARMORSUIT PC-P50R new internal layout has the motherboard on top of the power supply, which creates more room for larger CPU cooler and easy access to the motherboard.
• The new 5.25" bay equipped a tool-less mounting bar incorporates with rubber padding to holds the 5.25" device in position, secured, and absorbs vibration.
• The aluminum PCI tool-less mounting module is equipped with a rubber pad which it is not only can hold the graphics card firmly, but also reduce noise as well as vibration while closing the gap.
• The ARMORSUIT PC-P50R enhance Power Supply installation and support with rubber pads on to mounting clip, it is aligned as well as reduced vibrations, making power supply more secure and without scratching the power supply paint.
• The power supply unit is at the bottom of the case. It can draw in cold air directly through the vent below the power supply. This cooler, fresh air will keep PS components cooler, stable and extend the PS life.
• The intake fans are aligned with inlet holes on the bezels. These are equipped with air filters to stop the dust and keep the internals dust free and clean.
• Special design for enthusiasts 2 water pipe inlets.
• The solid main chassis was folded with 1.5mm thick aluminum sheeting to make a more sturdy structure which has less vibration.
• There is an air filter at the base of the case to stop dust from entering the case. The filter is washable. The vents are specially designed to retard heat and fire crossover should a short circuit cause sparks and excessive heat within your system. This feature is designed to prevent the problem from spreading outside your case should the unlikely event occur with your components.

Lian Li Armorsuit PC-P50R Specifications

• Color: Red
• Material: Hard anodized aluminum
• Dimensions: 210 x 495 x 490 mm(W, H, D)
• Dimensions: 8.27 x 19.49 x 19.48 inch (W,H,D)
• Net Weight: 6.6 kg / 15 lb
• 5.25 inch drive bay (External): 9
• 3.5 inch drive bay (External): 0
• 3.5 inch drive bay (Internal): 3 ( using 6 x 5.25)
• Motherboard Type: E-ATX, ATX, M-ATX
• Motherboard Tray: Yes, Removable
• System Fan (Front): 1 x 12cm LED Fan @1200 RPM
• System Fan (Top): 2 x 14cm LED Fan @1000 RPM
• System Fan (Rear): 1 x 12cm Fan @1500RPM
• I/O Ports: USB 2.0 x 4; HD+AC97 Audio
• Expansion Slots: PCI x 8

About the company: Lian Li

Lian Li Industrial Co., LTD was founded in 1983. We are the one of the largest and most reputable manufacturer of aluminum PC case in Taiwan. With over twenty years of experience in the computer products field, our dedicated team of engineers, production specialists and administrative staff provide the finest quality accessories available on the market.

In 1993, Lian-Li Introduced the new lines of computer hardware, including bracket (for case & interfaces), Mobile rack (for H.D.D.), mounting kit (for FDD & HDD), aluminum PC cases, IPC, external cases, server cases and more. We also provide OEM & ODM services, you are assured of designs that will meet your exact specifications, and innovative ideas in manufacturing that will give your products an essential market edge.

Our outstanding quality has earned us ISO 9001 certification for all of our products. In addition, we back up our quality assurance with a two-year guarantee on most of our products. R&D is one of the reasons why Lian Li is able to offer quality products to the market. Whether it is for OEM or ODM projects, our experienced mechanical and electrical engineers are capable of providing our customers with the best solutions in product design.

Previous Page - Next Page >>