«

»

ASUS Sabertooth Z97 Mark 1 Motherboard Review

PAGE INDEX

<< PREVIOUS            NEXT >>

TUF Motherboard Thermal Armor

The signature feature of ASUS’ Sabertooth motherboard is the Thermal Armor system. It has evolved over the years and currently comprises a plastic top plate with ventilation holes over the voltage regulator modules around the CPU socket that can be opened or closed, mounting places for two 40mm “assistant” fans, and a heavy steel back plate that serves both to keep the motherboard from flexing under the load of heavy CPU coolers and video cards, and also acts as a heat sink to some of the aforementioned VRMs.

asus_z97_sabertooth_rot3

The two helper fans are installed between the CPU and the first PCI-E x16 slot…

asus_z97_sabertooth_accessory_fan1

…as well as by the rear I/O panel:

asus_z97_sabertooth_accessory_fan2

In both cases the fans blow air inwards from the outside of the system, although by default they both run in reverse at high speed for 30 seconds at boot time to help remove dust. The fans are fully under the control of ASUS’ Thermal Radar 2 system and can be controlled like any other fan connected to the system. At full speed, these fans exceed 6,000 RPM and emit a high-pitched whine, although you’ll normally only hear this at start time. Even under heavy load, the normal speed didn’t exceed about 4,500 RPM. The fans are definitely audible in this case although not obtrusive. You can configure the fans to run for a period of time after system shutdown to exhaust hot air from under the Thermal Armor shrouding.

The Thermal Armor system can be easily removed, although there are a fair number of screws involved. With the armor off, the Sabertooth Z97 Mark 1 has a more standard appearance. The black heat sinks around the processor VRM modules are much less showy than the heat sinks ASUS uses on their other boards, but of course they won’t normally be visible.

asus_z97_sabertooth_naked_top

On the back of the TUF Fortifier steel backplate we can see a thermal pad that contacts the bottom of the motherboard, helping to cool the power circuitry between the CPU and the I/O panel.

asus_z97_sabertooth_fortifier_thermal_padsASUS has always been a little vague in describing the benefits of Thermal Armor, so I decided to see for myself what it can do. Since the Sabertooth Z97 is festooned with temperature sensors, it was easy to run a simple test: overclock the system as far as I could (which was 44x on all cores at 1.3v), run the AIDA64 system stability test, and record the temperature reported by the onboard sensors without the two assistant fans, with the fans, and with the Thermal Armor removed. Here are the results:

(@22ºC) Idle Load( w/fans) Load (no fans) Load (no armor) Delta (w/fans vs. no armor)
CPU 32 78 77 73 -5
VCORE 47 54 56 59 +5
VCORE (rear) 33 38 49 48 +10
DRAM 32 34 35 33 -1
USB 3 37 38 44 38 +0
PCIE 1 33 34 38 35 +1
PCIE 2 32 33 36 33 +0
MB 27 29 30 30 +1
PCH (Z97) 36 38 42 41 +3

The results are interesting. Comparing the maximum temperatures recorded with the Thermal Armor and assistant fans installed with the temperatures records with the Thermal Armor removed, 7 of the 9 points measure showed higher temperatures without the armor. The biggest delta is the rear VCORE temperature, which is a startling 10ºC warmer under load with the armor removed. I expected the rear VCORE to show higher temps since the rear assistant fan blows directly over these components when it’s installed. The one real oddity in this table was that the CPU load temperature dropped 5ºC with the armor removed, which I can’t explain, since the Thermalright Silver Arrow heat sink is completely outside the influence of the armor.

It’s also obvious that you should definitely install the assistant fans. In every case except the CPU, load temperatures were higher without the fans. I did try the load test with the fans with the VRM venting open and closed, but I didn’t see any difference in temperature.

ASUS doesn’t position this motherboard as an overclocking monster, but let’s see what we can do anyway in the next section.


SKIP TO PAGE:

<< PREVIOUS            NEXT >>

5 comments

Skip to comment form

  1. f doggrell

    will the asus sabertooth z97 mark 1 ( or mark 2 ) be fully compatible with the new broadwell cpu ? when will intel finally start selling the broadwell ? great review . thanks .

    1. Caring1

      It will be backwards compatible with current gen Intel processors as well, but you will lose some of the functionality. You will not be able to use Broadwell processors on current gen motherboards.

      1. David Ramsey

        Just to clarify: we know you will be able to use Broadwell CPUs on motherboards with Z97 chipsets. Older chipsets, well, I haven’t heard anything official either way.

  2. David Ramsey

    Broadwell support is the main reason for the existence of the Z97 chipset, so yes, any new motherboard with a Z97 will support Broadwell, although it wouldn’t surprise me if you had to update the BIOS when Broadwell comes out. As to when Intel will start selling Broadwell CPUs: well, it was originally supposed to be late 2nd quarter, but has slipped since then. Hopefully some time this year.

  3. James

    Re the mystery pins, I think it actually says “LPC DEBUG” so I’m guessing it might be to hook up something similar to this: http://amzn.to/1oedVBz

Leave a Reply

Your email address will not be published. Required fields are marked *

CAPTCHA Image

*

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>