Noctua NH-U14S 140mm Tower CPU Cooler Review


<< PREVIOUS            NEXT >>

Detailed Features: Noctua NH-U14S

While the shape is pretty typical of tower coolers, there are some detailed features that remain unique to Noctua – so let’s take a look.


This has got to be one of the finest mirror polishes I’ve seen on a factory CPU cooler. A little of the machining marks are visible, but the surface itself is highly polished. I tried to capture the very slight convex surface of the contact plate, which should result in a superior application of thermal interface material (as well as greater contact pressure right over the hottest part of most CPUs).


If you look closely, you can see some of the wavy machining marks in the mounting surface of the NH-U14S, but these marks are completely covered by a very high quality mirror finish. I really should have flipped the tube of included Noctua NT-H1 thermal paste so you could see the letters reflected in the cooler’s surface – Noctua really cements their reputation as a premium distributer of CPU cooling products with details like this. It’s rare that manufacturers will take the time to polish the mating surface of their coolers to this extent; maybe it’s only good for a degree of performance but as we’ll see later these small details add up.


The NH-U14S uses Noctua’s SecuFirm2 Mounting System. Containing a different set of brackets depending on the socket you’re installing the cooler on, all of the pieces you’ll need are in a nicely labeled box (with common components in a third box). For the AM3+ socket on the testbed, this consists of four standoffs and two brackets (with four screws to attach them all). It’s a little unfortunate that you won’t be able to choose the orientation of the cooler (at least on AMD sockets), but for many systems this won’t be a problem and is a common approach with tower coolers anyway.


Installing the heatsink is easy, but you’ll still need to remove the fan to do so. It was here I found myself drifting back to the SilverStone Argon coolers I had tested a few months ago – the fan mounting system they had developed made this process much easier. Yes, it’s splitting hairs (metal clips aren’t that hard to work with either) but it shows there’s still room for innovation.


The NH-U14S showcases the NH-U series selling point of RAM clearance. The heatsink’s width (depth) of 52mm means even fans on both sides won’t intrude on the DIMM slots (of course, this is if the motherboard manufacturer follows the socket area specifications of AMD and Intel – ITX boards are usually a toss-up if a cooler will fit or not).


Adding a second fan involves swapping out the brown vibration-dampening corners with the thicker set included in the NH-U14S accessory box. Seen in the picture above, these will add a bit of space in front of the fan blades which I’m sure helps to cut down on noise (moving blades placed against stationary fins/mesh/filters tend to emit all sorts of sounds). I did test the NH-U14S in a push/pull configuration, and it resulted in a 1.2C change (for the better). This is pretty typical of most of the heatsinks I test – while I don’t normally include the results of push/pull setups I’ll commonly throw an extra fan on a heatsink out of curiosity. So far, most 140mm-sized heatsinks will usually shed about one degree Celsius with an additional fan, and the Noctua is no different. The larger mass and additional heatpipes generally mean more surface area – essentially the larger the heatsink, the less help it needs to shed heat. Smaller heatsinks tend to benefit more from adding another fan, as the smaller surface area usually needs the extra help to remove the heat from the heatsink.

Usually I don’t include these results as the extra noise and cost are rarely worth the small performance gain. In the Noctua’s case though, adding a premium fan like the NF-A15 didn’t add much noise at all – while still an expensive improvement, at least it remains a quiet one. This makes it an easier option to consider if you really need an extra bump in performance.


<< PREVIOUS            NEXT >>

1 comment

  1. Chris

    Hey Tom,

    It’s interesting watching the CPU cooler battle go back and forth. This super-tower, in dual fan configuration seems to do pretty well, even compared to the dual towers.

    I know that this is a bit off topic for this review, but have you ever seen Cryrorig’s AF41?

    See here:

    Basically, that is a 4 tower cooler. Not sure if it will ever go on sale though.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>